Plumber's Essentials: Your Key to Installing a Bathtub
Plumber's Essentials: Your Key to Installing a Bathtub
Blog Article
How do you really feel in regards to A Step-by-Step Guide to Installing a Bathtub?
Installing a tub isn't precisely brain surgery, but it does need strong plumbing, carpentry, and also often, tiling skills. Changing an old tub with a new one is additionally a moderately difficult project. If the old bathtub is easily accessible, the job can relocate rapidly; if you have to open up a wall surface to remove the old bathtub as well as position the new bathtub, the job is much harder. In either case, the project is within a home handyman's abilities, although you will certainly need a helper to leave the old bathtub and set in the brand-new one. Make sure you have actually qualified yourself for the work and also fit trying it. Instead of hiring a service provider to take control of a halfway-completed job, it is far better to take into consideration utilizing one prior to you begin. Possibilities are you may need an expert plumber to make tube links.
This post will certainly aid you mount a brand-new bathtub in your restroom if you have already acquired a new tub and also don't require to change the plan of your previous water pipelines.
Your tools and product list must comprise the following:
Preparing for the Setup
First of all, the supporting structure supplied with the bath needs to be fitted (if required) according to the manufacturer's instructions. Next, fit the taps or mixer to the tub. When fitting the tap block, it is necessary to ensure that if the faucet features a plastic washing machine, it is fitted in between the bath as well as the faucets. On a plastic bath, it is likewise reasonable to fit a sustaining plate under the taps unit to prevent pressure on the bath tub.
Fit the adaptable faucet adapters to the bottom of both taps making use of 2 nuts and also olives (in some cases provided with the tub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink electrical outlet hole, and after that pass the outlet with the hole in the bathroom. Use the nut provided by the maker to fit the plug-hole. Check out the plug-hole outlet for an inlet on the side for the overflow pipeline.
Next off, fit completion of the adaptable overflow pipe to the overflow electrical outlet. After that, screw the pipeline to the overflow face which should be fitted inside the bath. See to it you make use of all of the provided washers.
Connect the catch to the bottom of the waste outlet on the tub by winding the string of the waste electrical outlet with silicone mastic or PTFE tape, and also screw on the catch to the electrical outlet. Connect the bottom of the overflow tube in a comparable manner.The bath must now be ready to be suited its final position.
Removing Old Taps
If you need to replace old taps with new ones as a part of your installation, after that the first thing you should do is detach the supply of water. After doing so, activate the faucets to drain any type of water staying in the system. The procedure of removing the existing taps can be rather bothersome due to the limited accessibility that is usually the situation.
Make use of a basin wrench (crowsfoot spanner) or a faucet tool to reverse the nut that attaches the supply pipelines to the faucets. Have a cloth ready for the continuing to be water that will certainly come from the pipelines. As soon as the supply pipes have actually been gotten rid of, utilize the same tool to loosen the nut that holds the faucets onto the bath/basin. You will certainly require to stop the solitary taps from turning during this procedure. When the faucets have actually been eliminated, the holes in the bath/basin will have to be cleaned of any type of old securing compound.
Before going on to fit the brand-new faucets, contrast the pipeline connections on the old taps to the brand-new faucets. If the old faucets are longer than the brand-new taps, after that a shank adapter is required for the new taps to fit.
Setting up the Bath tub
Utilizing both wood boards under its feet, place the bathtub in the needed position. The wood boards are handy in equally spreading the weight of the bathtub over the location of the boards as opposed to focusing all the weight onto four tiny factors.
The next objective is to make certain that the bathtub is leveled all round. This can be accomplished by checking the spirit level and adjusting the feet on the bathtub until the spirit level reviews level.
To mount faucets, fit all-time low of the furthest adaptable tap port to the proper supply pipe by making a compression sign up with; after that do the very same for the other faucet.
Activate the water system as well as check all joints as well as new pipework for leakages and also tighten them if essential. Fill the bathtub and additionally examine the overflow electrical outlet and the typical outlet for leaks.
Ultimately, deal with the bath paneling as described in the maker's instruction manual. Tiling as well as sealing around the bathtub must wait until the bath tub has been utilized at least once as this will settle it right into its final setting.
Suitable New Touches
If the tails of the brand-new faucets are plastic, then you will need a plastic connector to stop damages to the string. One end of the port fits on the plastic tail of the tap as well as the other end gives a connection to the current supply pipelines.
If you require to fit a monobloc, after that you will certainly require decreasing couplers, which attaches the 10mm pipe of the monobloc to the typical 15mm supply pipeline.
Next, place the faucet in the mounting opening in the bath/basin ensuring that the washing machines remain in place in between the tap and the sink. Secure the faucet in place with the producer given backnut. As soon as the faucet is firmly in position, the supply pipelines can be attached to the tails of the taps. The faucets can either be attached by utilizing corrugated copper piping or with typical faucet ports. The previous type should be connected to the faucet ends initially, tightening up only by hand. The supply pipes can later be linked to the other end. Tighten up both ends with a spanner after both ends have actually been linked.
Tiling Around the Bathtub
In the area where the bath fulfills the floor tile, it is required to seal the joins with a silicone rubber caulking. This is very important as the installation can move enough to crack a rigid seal, causing the water to pass through the wall in between the bath and also the tiling, bring about difficulties with wetness and also possible leakages to the ceiling below.
You can choose from a selection of coloured sealants to blend in your fixtures as well as installations. They are sold in tubes and cartridges, as well as can sealing spaces approximately a width of 3mm (1/8 inch). If you have a larger space to load, you can load it with spins of drenched paper or soft rope. Keep in mind to constantly fill up the bathtub with water before securing, to permit the movement experienced when the tub remains in use. The sealer can break fairly very early if you do not think about this movement before sealing.
Conversely, ceramic coving or quadrant floor tiles can be used to edge the bath or shower tray. Plastic strips of coving, which are easy to use and also reduce to dimension, are likewise conveniently offered on the market. It is advisable to fit the tiles using waterproof or water resistant sticky as well as cement.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
I found that page about How to Install a Bathtub when perusing the search engines. Liked our write up? Please share it. Help somebody else discover it. Thanks for your time. Don't forget to come by our website back soon.
Ready anytime, dial! Report this page